Contact US

AUGUST - OCTOBER 2026

TBA

CENTRAL & SOUTH AMERICA TRAINING CONFERENCE 2026
  • Cancún, Mexico - Santiago, Chile - São Paulo, Brazil
Secure your seat now
Download Brochure
view all courses
Limited Seats. Secure your seats now.

CERTIFICATED COURSES

In August 2026, aviation safety professionals from across Central & South America and the surrounding region will come together for a comprehensive multi-course training conference focused on Flight Data Analysis, Cockpit Voice Analysis, Flight Data Monitoring, and Data Troubleshooting. This event will feature our full suite of certificated courses, offering valuable development opportunities for both new analysts and seasoned specialists.
Cancún, Mexico
  • ADA 214 – E170-195 Flight Data Analysis [Aug 24 - 28]
  • ADA 202 – A318-A321 Flight Data Analysis [Aug 31 - Sep 4]
Santiago, Chile
  • ADA 202 – A318-A321 Flight Data Analysis [Sep 7 - 11]
  • ADA 210 – 757/767 Flight Data Analysis [Sep 14 - 18]
  • ADA 211 – 777 Flight Data Analysis [Sep 21 - 25]
São Paulo, Brazil
  • ADA 215 – ATR 72 Flight Data Analysis [Oct 5 - 9]
  • ADA 202 – A318-A321 Flight Data Analysis [Oct 19 - 23]
  • ADA 208 – 737 NG & Max Flight Data Analysis [Oct 26 - 30]

TRAINING SITE

Marriot Hotels & Conference Centers

Experience CENTRAL & South America

Beyond the classroom, participants may enjoy:
  • The vibrant beaches, nightlife, and coastal beauty of Cancún
  • The iconic landscapes, oceanfront scenery, and energy of Rio de Janeiro
  • Or the unique experiences offered by another selected destination in the region
Expect an unforgettable combination of world-class training and immersive cultural exploration!
Got any questions or inquiries?
Our team can walk you through how Flight Data X works, what the analytics uncover, and how it fits into your operation. Reach out whenever you need clarity.
CONTACT OUR TEAM
or email us at courses@flightdatax.com

Contact our Team

I failed my annual FDR readout for my helicopter due to a missing rotor speed. How can I address this?

First make sure the signal/sensor output is available on your helicopter. Next, upgrade your CVR to a model which has rotor speed capability. If you require certification assistance, we can help.

Close

I need to synchronize my FDR and CVR data due to an aircraft incident we just had. How can I go about this?

Locate the sample where your FDR radio altitude reached 50 foot (+/-) on approach and match that up with your CVR audio callout at 50 feet. Next, create a chart correlating the audio time to your GMT time based on the initial 50 foot synchronization you have established. If you find this difficult, you can also attend our CVA 101 course where we teach students how to synchronize CVR and FDR data.

Close

Learn more about how Flight Data Simulation can benefit your organization.

Learn more about how Flight Data Simulation can benefit your organization.

Learn more about how DAE for Aerospace can benefit your organization

How do I modify my FDR to record more than 25 hours?

You can modify the program pins at the rear of the SSFDR to uptick your recording hours. For example, if you have a Honeywell PN 980-4700-XXX installed, you can alter the ‘ground/open’ discrete wiring at pin 17 & 18 of the SSFDR mating connector to increase your recording capacity.

Close

How can I determine the amount of hours recorded by my FDR?

The amount of recorded hours is dependent on a combination of your FDAU wps output and FDR maximum allowable recording speed. If there is a one to one relationship between the two units, i.e. – 64 wps FDAU with a 64 wps FDR, you will record the last 25 hours of flight data. This also applies to the case when the FDAU and FDR are both 128wps, 256wps, or even higher. If there is a mismatch between the FDAU and FDR speed, a small and simple calculation can be made to determine actual flight hour recording capacity. See the figure below for the various possibilities:

Close

How can I determine the speed of my Flight Data Recording system in words per second (wps)?

There are basically 4 ways to determine your speed, with the 4th being a bit more involved. First, the speed should be listed or documented in chapter 31 of your aircraft Maintenance Manual and/or Wiring Diagram Manual. However there are times when for some reason, the required information cannot be found. If this is the case, as a second method, you may reference the CMM or technical specification for your Flight Data Acquisition Unit (FDAU). If you are still unable to find this information, you may contact the aircraft manufacturer for the wps or review your previous FDR download analysis reports. Please keep in mind, the OEM will only know the as-delivered configuration of your aircraft. If there were modifications to your aircraft post-delivery – manufacturer unaware of the changes – youll need to contact us for an analysis of your raw data. Using our software we can determine the wps of your system.

Close

With regard to Flight Data Recorder Systems, what exactly does wps imply? I have noticed this abbreviation in our FDR documentation and in communications with the manufacturer several times:

WPS = words per second. A word (12-bits in length) contains binary data which represents a specific parameter value. Please see figure 1 below. Your FDR records in frames (4 second intervals) and each frame contains 4 sub frames (one sub frame = 1 second). With each second that goes by a specific quantity of words are recorded into memory. If you operate a 64 wps FDR system, you will record 64 12-bit words in one second. The higher the word capacity the more information you can record.

Close

What is a Dataframe Layout (DFL)?

A DFL, also known by the name Logical Frame Layout (LFL), Dataframe Interface Control & Requirements Document, and many other names depending on the manufacturer, is a document which specifies the FDR, QAR, or DAR Parameter Word (location), Recording Speed, Sampling Rate, Bits, and Conversion formulae for your recording system.  

Close

Contact our Team