Contact US

10-14 AUGUST 2026

CASABLANCA, MOROCcO

MOROCCO TRAINING EVENT 2026
  • Casablanca, Morocco
Secure your seat now
Download Brochure
view all courses
Limited Seats. Secure your seats now.

CERTIFICATED COURSES

In August 2026, Flight Data X will host an exclusive aviation safety training event in Casablanca a strategic aviation hub connecting Africa, Europe, and beyond. This premier session is designed for aviation professionals looking to strengthen their expertise in flight data monitoring, safety analysis, and investigative techniques.
  • FDA101 – Introduction to Flight Data Analysis [Aug 10 - 12]
  • CVA101 – Introduction to Cockpit Voice Analysis [Aug 13 - 14]
Bringing together industry specialists from around the world, the event delivers a focused, practical learning experience through certified training programs. Participants will gain real-world skills register now to secure your place.

TRAINING SITE

Marriot Hotels & Conference Centers​

WHY ATTEND?

  • Learn from experienced aviation safety professionals
  • Gain hands-on exposure to real-world data scenarios
  • Strengthen your technical and analytical skillset
  • Earn recognized certification in flight data disciplines
  • Network with industry experts and peers
Got any questions or inquiries?
Our team can walk you through how Flight Data X works, what the analytics uncover, and how it fits into your operation. Reach out whenever you need clarity.
CONTACT OUR TEAM
or email us at courses@flightdatax.com

Contact our Team

I failed my annual FDR readout for my helicopter due to a missing rotor speed. How can I address this?

First make sure the signal/sensor output is available on your helicopter. Next, upgrade your CVR to a model which has rotor speed capability. If you require certification assistance, we can help.

Close

I need to synchronize my FDR and CVR data due to an aircraft incident we just had. How can I go about this?

Locate the sample where your FDR radio altitude reached 50 foot (+/-) on approach and match that up with your CVR audio callout at 50 feet. Next, create a chart correlating the audio time to your GMT time based on the initial 50 foot synchronization you have established. If you find this difficult, you can also attend our CVA 101 course where we teach students how to synchronize CVR and FDR data.

Close

Learn more about how Flight Data Simulation can benefit your organization.

Learn more about how Flight Data Simulation can benefit your organization.

Learn more about how DAE for Aerospace can benefit your organization

How do I modify my FDR to record more than 25 hours?

You can modify the program pins at the rear of the SSFDR to uptick your recording hours. For example, if you have a Honeywell PN 980-4700-XXX installed, you can alter the ‘ground/open’ discrete wiring at pin 17 & 18 of the SSFDR mating connector to increase your recording capacity.

Close

How can I determine the amount of hours recorded by my FDR?

The amount of recorded hours is dependent on a combination of your FDAU wps output and FDR maximum allowable recording speed. If there is a one to one relationship between the two units, i.e. – 64 wps FDAU with a 64 wps FDR, you will record the last 25 hours of flight data. This also applies to the case when the FDAU and FDR are both 128wps, 256wps, or even higher. If there is a mismatch between the FDAU and FDR speed, a small and simple calculation can be made to determine actual flight hour recording capacity. See the figure below for the various possibilities:

Close

How can I determine the speed of my Flight Data Recording system in words per second (wps)?

There are basically 4 ways to determine your speed, with the 4th being a bit more involved. First, the speed should be listed or documented in chapter 31 of your aircraft Maintenance Manual and/or Wiring Diagram Manual. However there are times when for some reason, the required information cannot be found. If this is the case, as a second method, you may reference the CMM or technical specification for your Flight Data Acquisition Unit (FDAU). If you are still unable to find this information, you may contact the aircraft manufacturer for the wps or review your previous FDR download analysis reports. Please keep in mind, the OEM will only know the as-delivered configuration of your aircraft. If there were modifications to your aircraft post-delivery – manufacturer unaware of the changes – youll need to contact us for an analysis of your raw data. Using our software we can determine the wps of your system.

Close

With regard to Flight Data Recorder Systems, what exactly does wps imply? I have noticed this abbreviation in our FDR documentation and in communications with the manufacturer several times:

WPS = words per second. A word (12-bits in length) contains binary data which represents a specific parameter value. Please see figure 1 below. Your FDR records in frames (4 second intervals) and each frame contains 4 sub frames (one sub frame = 1 second). With each second that goes by a specific quantity of words are recorded into memory. If you operate a 64 wps FDR system, you will record 64 12-bit words in one second. The higher the word capacity the more information you can record.

Close

What is a Dataframe Layout (DFL)?

A DFL, also known by the name Logical Frame Layout (LFL), Dataframe Interface Control & Requirements Document, and many other names depending on the manufacturer, is a document which specifies the FDR, QAR, or DAR Parameter Word (location), Recording Speed, Sampling Rate, Bits, and Conversion formulae for your recording system.  

Close

Contact our Team